How to connect multiple TVs to one antenna

Many users at home are not one, but two or three TVs. And although, before, even one TV device was considered an inadmissible luxury, now two TVs in one house are considered normal. However, many owners of several televisions are wondering if it is possible to connect more than one screen to one antenna. This need is primarily due to savings, since it is much more convenient to use one antenna for all TVs than to connect to each TV device via a separate antenna. Also, the need to connect different devices to one antenna is caused by the impossibility of high-quality reception of signals on all sides of a house or apartment. In other words, it is easier for the user to ensure good signal reception on one antenna than to individually configure each receiving device.

Can I connect multiple TVs to the same antenna?

You can connect multiple TVs to one antenna. To do this, it is enough to use a special splitter, which will allow for the transmission of signals through two cables instead of one.

How many TVs can be connected to one antenna.

In the presence of special knowledge and skills, the number of connected TVs is not limited. This requires only special splitters or adapters that duplicate the incoming signal to two cables. However, the user should remember that each connected adapter or splitter degrades the signal quality, and connecting more than five devices to one antenna is not practical.

How to connect multiple TVs to one antenna.

The easiest and most convenient way is to use a conventional splitter. There are two types of splitters: passive and active. Let us dwell on them in more detail.

1. Passive splitters usually consist of conventional transistors or resistors. They simply split the signal into two identical ones and transmit them further on two cables. The main problem of this technology is that when separated, the output signal is attenuated by half, therefore, only 50% of the initial information will come to the terminal device. This is not very critical for two televisions, but if the signal is divided into 3 or 4 parts, the image deteriorates significantly, which becomes noticeable to the naked eye.
2. Active splitters, in turn, allow you to save the signal quality, thanks to the power amplification cascade, which is contained in the circuit of these devices. These splitters transmit a signal with minimal power loss to several devices. However, these devices have a significant minus - they provide only one-way communication.

Many Internet service providers transmit information over the same cable as the television. This makes it impossible for the Internet to work when an active splitter is connected, since its operation requires feedback. To avoid such problems, a passive splitter must first be installed on the common cable. And from it an Internet cable will go to one output, and to another cable with a television signal, which will, in turn, be connected to a passive splitter.

ATTENTION. It should be remembered that the loss of signal quality can be not only due to a bad splitter, but also due to poor-quality cable.

Connect two TVs

Below is a step-by-step instruction for connecting two devices to the antenna through a conventional splitter.

1. First, carefully strip the cable without damaging the screen and foil.
2. Then roll the foil around the wire. In this case, the central core should not touch the foil.
3. Screw the connector onto the cable.
4. The next step is to connect the cable to the divider.

After that, the user has the opportunity to watch TV from one antenna on two devices.

How to connect three TVs

In order to connect three TVs, use an active splitter. The cable from the antenna should be connected to a divider with a cascade of amplification, and from it run the cable to another splitter. The latter can be either passive or active, since the input gain is sufficient for correct operation. The process of connecting the cable to the active splitter is the same as to the passive one.

The main problems and ways to fix them.

1. Bad image. First of all, this problem can be caused by a poor-quality splitter or cable. Perhaps the insulation is broken somewhere or the connector is damaged. The component components should be replaced, and if the picture has not improved, then the problem is different. Also, the cause of a bad signal may be in the antenna itself. If there is interference, you should try to change the location or turn of the antenna and look at changes in image quality.
2. Image is missing. If there is no signal at all, pay attention to the divider. Usually active dividers have a connector for additional power. Also, it is possible that the problem is a faulty antenna or a broken connector on the TV itself. You should try working with another antenna or with another TV device.

It should also be remembered that an Internet connection does not work with an active splitter, since such devices do not have feedback.