One of the most important elements of the bath room, of course, is the boiler. But even if you have already chosen the perfect model and managed to get it, you still have one more task: to install the boiler in the bathhouse. How to do it by all the rules and not be disappointed in the purchase? Is it possible to install everything yourself without resorting to the help of professionals? You will learn about all this in this article.
What are the boilers for the bath
To begin, consider the types of such units. This is important because each model has its own characteristics that should be considered during installation.
Boilers are distinguished by several criteria. For example, for the fuel used:
- electric;
- pyrolysis;
- gas;
- solid fuel;
- liquid fuel.
The gas-fired version is the most compact and economical, and there is no unpleasant odor during operation. He also does not need ventilation, but with all its advantages, it can qualitatively heat a rather large area. This is the best option if gas is routed to your site.
An electrical appliance is considered the most environmentally friendly. In advantages, it is in no way inferior to gas, but it will have to be taken into account that the cost of electricity will increase significantly.
Solid fuel models work from firewood or peat. It is noted that such boilers remarkably maintain the required temperature for a long time, but they have to be constantly replenished with fuel. In automatic mode, they work only a few hours, the exact time depends on the capacity of the fuel tank.
Liquid fuel is characterized by ease of storage, but boilers working from it very often emit unpleasant odors that can ruin all the pleasure of visiting a steam room. Therefore, such models are recommended to be installed in a separate room.
The pyrolysis options please the owner with the fact that they practically do not leave soot or other unpleasant fuel wastes - everything completely burns out with the help of two special chambers installed inside the device.
The difference between the boiler and the stove
It should be understood that the boiler and the furnace are far from the same, although both of these devices perform similar functions.. The boiler is a kind of part of the heating system, which is installed in the bath much less often than the widespread stove. But in special cases, when an element is needed to supplement the power of the furnace, it will be necessary.
A stove is what directly warms the room, and the boiler transfers heat to another carrier. It is installed, for example, if the stove is low-power or the bath cannot be connected to the hot water supply system.
IMPORTANT! Very often in unverified sources you can find information that the boiler and furnace are synonyms that successfully replace each other, but this is not so. Now you know what their significant difference is and you can approach the issue of the need to install the boiler correctly.
DIY boiler installation
It is quite possible to cope with the installation of the boiler yourself, but keep in mind that in the event of a breakdown some manufacturers may refuse from their warranty obligations, arguing that the installation was not performed correctly. However, even an appeal to professionals will not in this case be a guarantee of quality.
In most cases, a detailed instruction is provided with the device to facilitate installation of the unit. It has a special scheme, which is better not to ignore.
There are several rules that must be considered when working. Violation of these rules may result in fire or damage to important elements of the heating system.
- The ceiling above the boiler and the chimney outlet must be covered with a metal sheet.
- The location of the boiler in the bath usually takes place in such a way that, if necessary, it was also possible to warm the dressing room or other additional room. In most cases, this effect is achieved by the location of the heating equipment in the dressing room, and the boiler itself - in the steam room.
- Do not forget about basic safety rules: a fire extinguisher should always be in the bath, and the floor should be covered with an anti-slip coating.
Installation must be in strict sequence. First, the foundation is being built. This is an important point, which is better to foresee during the construction of the bath, but if this was not done, do not worry. After that, the boiler itself is installed on the foundation. The next step will be the installation of the chimney.
IMPORTANT! Do not forget to reliably seal any gaps. Otherwise, an accident may occur at the first use.
Lastly, a rain hood is installed.
Thus, it is not so difficult to install the boiler in the bath, especially if you have instructions from the manufacturer who calculated all the parameters taking into account his professional knowledge in this area.
Leave Your Comment